View UPD23C64300F9-XXX-BC3_1332278.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DATA SHEET
MOS INTEGRATED CIRCUIT
PD23C64300
64M-BIT MASK-PROGRAMMABLE ROM 8M-WORD BY 8-BIT (BYTE MODE) / 4M-WORD BY 16-BIT (WORD MODE)
Description
The PD23C64300 is a 67,108,864 bits mask-programmable ROM. The word organization is selectable (BYTE mode : 8,388,608 words by 8 bits, WORD mode : 4,194,304 words by 16 bits). The active levels of OE (Output Enable Input) can be selected with mask-option. The PD23C64300 is packed in 48-pin TAPE FBGA.
Features
* Pin compatible with NOR Flash Memory * Word organization 8,388,608 words by 8 bits (BYTE mode) 4,194,304 words by 16 bits (WORD mode) * Operating supply voltage : VCC = 2.7 V to 3.6 V
Operating supply voltage VCC 3.0 V 0.3 V 3.3 V 0.3 V Access time ns (MAX.) 100 90 Power supply current (Active mode) mA (MAX.) 40 55 Standby current (CMOS level input)
A (MAX.)
30
The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version.
Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information.
Document No. M16056EJ4V1DS00 (4th edition) Date Published July 2004 NS CP(K) Printed in Japan
The mark shows major revised points.
2002
PD23C64300
Ordering Information
Part Number Package 48-pin TAPE FBGA (8 x 6)
PD23C64300F9-xxx-BC3
(xxx : ROM code suffix No.)
Marking Image
Part Number Marking ( A )
PD23C64300F9-xxx-BC3
J R64 -xxx
ROM code suffix No.
INDEX MARK
Lot No.
2
Data Sheet M16056EJ4V1DS
PD23C64300
Pin Configuration
/xxx indicates active low signal. 48-pin TAPE FBGA (8 x 6)
Top View
Bottom View
6 5 4 3 2 1
A
B
C
D
E
F
G
H
H
G
F
E
D
C
B
A
A 6 A13
B A12
C A14
D A15
E A16
F WORD, /BYTE
G O15, A-1 O13 VCC O11 O9 /OE or OE
H GND 6
H GND
G O15, A-1
F WORD, /BYTE O14 O12 O10 O8 /CE
E A16
D A15
C A14
B A12
A A13
5 4 3 2 1
A9 NC NC A7 A3
A8 NC NC A17 A4
A10 A21 A18 A6 A2
A11 A19 A20 A5 A1
O7 O5 O2 O0 A0
O14 O12 O10 O8 /CE
O6 O4 O3 O1 GND
5 4 3 2 1
O6 O4 O3 O1 GND
O13 VCC O11 O9 /OE or OE
O7 O5 O2 O0 A0
A11 A19 A20 A5 A1
A10 A21 A18 A6 A2
A8 NC NC A17 A4
A9 NC NC A7 A3
A0 to A21
: Address inputs
O0 to O7, O8 to O14 : Data outputs O15, A-1 : Data output 15 (WORD mode), LSB Address input (BYTE mode) WORD, /BYTE /CE /OE or OE VCC GND NC DC
Note
: Mode select : Chip Enable : Output Enable : Supply voltage : Ground : No Connection : Don't Care
Note Some signals can be applied because this pin is not connected to the inside of the chip. Remark Refer to Package Drawing for the index mark.
Data Sheet M16056EJ4V1DS
3
PD23C64300
Input / Output Pin Functions
Pin name WORD, /BYTE Input / Output Input Function The pin for switching WORD mode and BYTE mode. High level : WORD mode (4M-word by 16-bit) Low level : BYTE mode (8M-word by 8-bit) A0 to A21 (Address inputs) Input Address input pins. A0 to A21 are used differently in the WORD mode and the BYTE mode. WORD mode (4M-word by 16-bit) A0 to A21 are used as 22 bits address signals. BYTE mode (8M-word by 8-bit) A0 to A21 are used as the upper 22 bits of total 23 bits of address signal. (The least significant bit (A-1) is combined to O15.) O0 to O7, O8 to O14 (Data outputs) Output Data output pins. O0 to O7, O8 to O14 are used differently in the WORD mode and the BYTE mode. WORD mode (4M-word by 16-bit) The lower 15 bits of 16 bits data outputs to O0 to O14. (The most significant bit (O15) combined to A-1.) BYTE mode (8M-word by 8-bit) 8 bits data outputs to O0 to O7 and also O8 to O14 are high impedance. O15, A-1 (Data output 15, LSB Address input) Output, Input O15, A-1 are used differently in the WORD mode and the BYTE mode. WORD mode (4M-word by 16-bit) The most significant output data bus (O15). BYTE mode (8M-word by 8-bit) The least significant address bus (A-1). /CE (Chip Enable) Input Chip activating signal. When the OE is active, output states are following. High level : High-Z Low level : Data out /OE or OE or DC (Output Enable, Don't care) VCC GND NC - - - Input Output enable signal. The active level of OE is mask option. The active level of OE can be selected from high active, low active and Don't care at order. Supply voltage Ground Not internally connected. (The signal can be connected.)
4
Data Sheet M16056EJ4V1DS
PD23C64300
Block Diagram
O8
O0
O1
O9
O2
O10
O11
O3
O12
O4
O5
O13
O6
O14
O15, A-1
O7
A0 A1 A2 A3 A4 A5 A6 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18
A19
A20
Address Input Buffer Y-Decoder
Output Buffer
Logic/Input
WORD, /BYTE /OE or OE or DC
Y-Selector
A7
Memory Cell Matrix
X-Decoder Input Buffer
4,194,304 words by 16 bits / 8,388,608 words by 8 bits
/CE
A21
Data Sheet M16056EJ4V1DS
5
PD23C64300
Mask Option
The active levels of output enable pin (/OE or OE or DC) are mask programmable and optional, and can be selected from among " 0 " " 1 " " x " shown in the table below.
Option 0 1 x /OE or OE or DC /OE OE DC OE active level L H Don't care
Operation modes for each option are shown in the tables below. Operation mode (Option : 0)
/CE L /OE L H H H or L Standby Mode Active Output state Data out High-Z High-Z
Operation mode (Option : 1)
/CE L OE L H H H or L Standby Mode Active Output state High-Z Data out High-Z
Operation mode (Option : x)
/CE L H DC H or L H or L Mode Active Standby Output state Data out High-Z
Remark L : Low level input H : High level input
6
Data Sheet M16056EJ4V1DS
PD23C64300
Electrical Specifications
Absolute Maximum Ratings
Parameter Supply voltage Input voltage Output voltage Operating ambient temperature Storage temperature Symbol VCC VI VO TA Tstg Condition Rating -0.3 to +4.6 -0.3 to VCC+0.3 -0.3 to VCC+0.3 -10 to +70 -65 to +150 Unit V V V C C
Caution Exposing the device to stress above those listed in Absolute Maximum Ratings could cause permanent damage. The device is not meant to be operated under conditions outside the limits described in the operational section of this specification. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Capacitance (TA = 25 C)
Parameter Input capacitance Output capacitance Symbol CI CO f = 1 MHz Test condition MIN. TYP. MAX. 10 12 Unit pF pF
DC Characteristics (TA = -10 to +70 C, VCC = 2.7 to 3.6 V)
Parameter High level input voltage Low level input voltage Symbol VIH VIL VCC = 3.0 V 0.3 V VCC = 3.3 V 0.3 V High level output voltage Low level output voltage Input leakage current Output leakage current Power supply current VOH VOL ILI ILO ICC1 IOH = -100 A IOL = 2.1 mA VI = 0 V to VCC VO = 0 V to VCC, Chip deselected /CE = VIL (Active mode), VCC = 3.0 V 0.3 V IO = 0 mA Standby current ICC3 VCC = 3.3 V 0.3 V -10 -10 Test conditions MIN. 2.0 -0.3 -0.3 2.4 0.4 +10 +10 40 55 30 TYP. MAX. VCC + 0.3 +0.5 +0.8 V V Unit V V
A A
mA
/CE = VCC - 0.2 V (Standby mode)
A
Data Sheet M16056EJ4V1DS
7
PD23C64300
AC Characteristics (TA = -10 to +70 C, VCC = 2.7 to 3.6 V)
Parameter Symbol Test condition VCC = 3.0 V 0.3 V MIN. Address access time Address skew time Chip enable access time Output enable access time Output hold time Output disable time WORD, /BYTE access time tACC tSKEW tCE tOE tOH tDF tWB 0 0 25 100 Note TYP. MAX. 100 10 100 25 0 0 25 90 VCC = 3.3 V 0.3 V MIN. TYP. MAX. 90 10 90 25 ns ns ns ns ns ns ns Unit
Note tSKEW indicates the following three types of time depending on the condition. 1) When switching /CE from high level to low level, tSKEW is the time from the /CE low level input point until the next address is determined. 2) When switching /CE from low level to high level, tSKEW is the time from the address change start point to the /CE high level input point. 3) When /CE is fixed to low level, tSKEW is the time from the address change start point until the next address is determined. Since specs are defined for tSKEW only when /CE is active, tSKEW is not subject to limitations when /CE is switched from high level to low level following address determination, or when the address is changed after /CE is switched from low level to high level. Remark tDF is the time from inactivation of Chip Enable input (/CE) or Output Enable input (/OE or OE) to high impedance state output. AC Test Conditions
Input waveform (Rise / Fall time 5 ns)
1.4 V
Test points
1.4 V
Output waveform
1.4 V
Test points
1.4 V
Output load 1TTL + 100 pF
8
Data Sheet M16056EJ4V1DS
PD23C64300
Cautions on power application To ensure normal operation, always apply power using /CE following the procedure shown below. 1) Input a high level to /CE during and after power application. 2) Hold the high level input to /CE for 200 ns or longer (wait time). 3) Start normal operation after the wait time has elapsed. Power Application Timing Chart 1 (When /CE is made high at power application)
Wait time /CE (Input) 200 ns or longer Normal operation
VCC
Power Application Timing Chart 2 (When /CE is made high after power application)
Wait time /CE (Input) 200 ns or longer Normal operation
VCC
Caution Other signals can be either high or low during the wait time.
Data Sheet M16056EJ4V1DS
9
PD23C64300
Read Cycle Timing Chart
tSKEW
A0 to A21, (Input) A-1 Note1
tSKEW
tSKEW
tACC
tACC
tACC
/CE (Input)
tCE
tDF Note2
tDF Note2
/OE or OE (Input)
tOE
O0 to O7, (Input) O8 to O15 Note3 High-Z
tOH
High-Z
tOH
tOH
Data out
Data out
Data out
Notes 1. During WORD mode, A-1 is O15. 2. tDF is the time from inactivation of Chip Enable input (/CE) or Output Enable input (/OE or OE) to high impedance state output. 3. During BYTE mode, O8 to O14 are high impedance and O15 is A-1.
WORD, /BYTE Switch Timing Chart
A-1 (Input)
High-Z
High-Z
WORD, /BYTE (Input) tOH tACC tOH tWB
O0 to O7 (Output)
Data Out
Data Out
Data Out
tDF High-Z
O8 to O15 (Output)
Data Out
Data Out
Remark
Chip Enable (/CE) and Output Enable (/OE or OE) : Active.
10
Data Sheet M16056EJ4V1DS
PD23C64300
Package Drawing
48-PIN TAPE FBGA(8x6)
wSB ZD ZE B
E
A D
6 5 4 3 2 1 HGFEDCBA
INDEX MARK
wSA
INDEX MARK
A y1 S A2 S
y
S
e
A1
M
b
x
S AB
ITEM D E w e A A1 A2 b x y y1 ZD ZE
MILLIMETERS 6.00.1 8.00.1 0.2 0.80 0.970.10 0.270.05 0.70 0.450.05 0.08 0.1 0.2 1.00 1.20 P48F9-80-BC3
Data Sheet M16056EJ4V1DS
11
PD23C64300
Recommended Soldering Conditions
Please consult with our sales offices for soldering conditions of the PD23C64300. Type of Surface Mount Device
PD23C64300F9-BC3
: 48-pin TAPE FBGA (8 x 6)
12
Data Sheet M16056EJ4V1DS
PD23C64300
Revision History
Edition/ Date This edition 4th edition/ Feb. 2004 Throughout Page Previous edition Throughout Deletion Ordering Information Package Type of revision Location Description (Previous edition This edition)
PD23C64300GZ-xxx-MJH
48-pin PLASTIC TSOP (I) (12 x 20) (Normal bent)
Data Sheet M16056EJ4V1DS
13
PD23C64300
[MEMO]
14
Data Sheet M16056EJ4V1DS
PD23C64300
NOTES FOR CMOS DEVICES
1 VOLTAGE APPLICATION WAVEFORM AT INPUT PIN Waveform distortion due to input noise or a reflected wave may cause malfunction. If the input of the CMOS device stays in the area between VIL (MAX) and VIH (MIN) due to noise, etc., the device may malfunction. Take care to prevent chattering noise from entering the device when the input level is fixed, and also in the transition period when the input level passes through the area between VIL (MAX) and VIH (MIN). 2 HANDLING OF UNUSED INPUT PINS Unconnected CMOS device inputs can be cause of malfunction. If an input pin is unconnected, it is possible that an internal input level may be generated due to noise, etc., causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND via a resistor if there is a possibility that it will be an output pin. All handling related to unused pins must be judged separately for each device and according to related specifications governing the device. 3 PRECAUTION AGAINST ESD A strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it when it has occurred. Environmental control must be adequate. When it is dry, a humidifier should be used. It is recommended to avoid using insulators that easily build up static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work benches and floors should be grounded. The operator should be grounded using a wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with mounted semiconductor devices. 4 STATUS BEFORE INITIALIZATION Power-on does not necessarily define the initial status of a MOS device. Immediately after the power source is turned ON, devices with reset functions have not yet been initialized. Hence, power-on does not guarantee output pin levels, I/O settings or contents of registers. A device is not initialized until the reset signal is received. A reset operation must be executed immediately after power-on for devices with reset functions.
Data Sheet M16056EJ4V1DS
15
PD23C64300
These commodities, technology or software, must be exported in accordance with the export administration regulations of the exporting country. Diversion contrary to the law of that country is prohibited.
* The information in this document is current as of July, 2004. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. * NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. * NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above).
M8E 02. 11-1

▲Up To Search▲

Price & Availability of UPD23C64300F9-XXX-BC3

	To Download UPD23C64300F9-XXX-BC3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .